Powered by
Digiseller
Digiseller
<delivery> ALTERNATIVE PLATFORMS FOR BANK CARD PAYMENT IF YOU ARE NOT FROM RUSSIA: Buy in Monecle: https://monecle.com/buy/52177 </delivery> Macros of the "No Recoil" class, that is, LUA scripts for Logitech G-series mice that support - Logitech Gaming Software and GHUB, in Call of Duty Modern Warfare 2019 (WarZone) almost completely remove vertical recoil from MG82. <attention> Attention!!! If you have a wireless mouse, or a monitor that is not 60Hz, or you have Windows 10 version 2004 and higher, then here are two scripts for the test on KILO141: https://macroleg.tech/product-category/download/ Script version v1.2 for Windows 10 versions 2004 and higher, use if v1.1 does not work. If the mouse sensitivity is set to 10.0 in the game, the FOV is 120, the sight leads strongly up or down. You'd better consult me before buying scripts.</attention> The scripts were written to adjust the sensitivity of the mouse in the game - 10.0, FOV - 100, under the mags for 100 rounds. But, for technical reasons, either when changing the FOV, or when modifying a weapon, if the sight pulls down during shooting, you reduce the values in the sensitivity settings of the mouse in the game, if up, you increase. If the mouse sensitivity settings in the game are too large for you, or too small, then you can change the dpi of your mouse, this will not affect the operation of the script. <delivery> Script management and script versions: </delivery> "5th mouse button" - turns on the script and the ScrollLock icon on the keyboard will light up. When pressed again, it turns off the script, the ScrollLock icon will go out. "Left shift + 5th mouse button" - then pressing the left mouse button will start shooting with recoil removal and aiming. If you are using AKIMBO, then clicking the left button will fire 2 shots. "v5.1 (v5.3)" - after the script is turned on, removal of recoil when left mouse button is pressed. "v5.2 (v5.4)" - removal of recoil in these scripts only in targeting mode, that is, with the right mouse button pressed. If you do not press the right button, the left button will work in its normal mode. "v5.1 and v5.2" are these versions of scripts for Windows 10 version 1909 and below. "v5.3 and v5.4" - these versions of scripts for Windows 10 version 2004 and higher, use if v5.1 and v5.2 do not work.
<delivery> After payment you will receive a link to download the archive with macros. If you accidentally closed the page with this link, you can return it by clicking on the link in the letter that came to your e-mail after payment. You can also go to your personal account at oplata.info and your purchase will be displayed there. </delivery> <attention>Problems that happen with Logitech and how to solve them!!!</attention> If you have a G304, G305, G602, G603, G604 or similar mouse that cannot be connected to a wire. And if your scripts do not work stably on it. Then you better sell such a mouse and buy yourself another, any wired Logitech, in order to use scripts normally. If you have a G600 mouse, then you should use only the GHUB program. If your scripts do not work stably on a wireless mouse, then you need to connect the wire and run GHUB or Logitech Gaming Software with administrator rights. Before installing the GHUB, you must have Logitech Gaming Software installed. The Logitech Gaming Software, or GHUB program is best run with administrator privileges. There have been cases of negative impact of Windows 10 version 2004 and higher on software from Logitech. Scripts may not work as they should and, if necessary, you need to increase the mouse sensitivity settings in the game. But, if this does not help, then you need to install Windows 10 version 1909, or lower. Sometimes the GHUB can is buggy, the scripts stop working and you need to reinstall it. Third-party programs that can use side mouse buttons, for example Diskord, can cause problems with running scripts, keep this in mind. Profiles for games in GHUB and Logitech Gaming Software, it is better not to use because of possible problems with anti-cheat. It is better to use a desktop profile with the "persistent" attribute. There is also a theory that a wi-fi router can interfere with the operation of a wireless mouse. If you have a lot of profiles, then script interruptions are possible. That is, at some point, there will be no recoil removal. You should also be familiar with the numbering of the mouse buttons.